 

################################################################################################
## Configuration template for firmware version 1.0.4.2 (HT488, HT496, HT386)
################################################################################################

##############################################################################
##  Advanced Settings.
##############################################################################

# Enable Provider Lock. 0 - No, 1 - Yes.
P9999 = 0

# Provider Lock Key. A string of up to 16 bytes.
P9998 = 

# Provider Authentication. A string of up to 16 bytes
P9997 = 

# Password for configuration file authentication
P1 = 

# Admin password for web interface
P2 = admin

# Home NPA
P259 =

# Layer 3 QoS (IP Diff-Serv or Precedence value for RTP)
P38 = 48

# VoIP Layer 2 QoS. 802.1Q/VLAN Tag (VLAN classification for RTP)
P51 = 0

# VoIP Layer 2 QoS. 802.1p priority value (0 - 7)
P87 = 0

# PC Layer 2 QoS. 802.1Q/VLAN Tag (VLAN classification for RTP)
# HT488/HT496 only
P229 = 0

# PC Layer 2 QoS. 802.1p priority value (0 - 7)
# HT488/HT496 only
P230 = 0

# STUN server
P76 = stun.mycompany.com

# Keep-alive interval (in seconds. default 20 seconds)
P84 = 20

# Use NAT IP.  This will enable our SIP client to use this IP in the SIP message. 
# Example 64.3.153.50.
P101 =

#-------------------------------------------------------------------------------
# Firmware Upgrade
#-------------------------------------------------------------------------------

# Firmware Upgrade and Privisioning. 0 - TFTP Upgrade,  1 - HTTP Upgrade.
P212 = 0

# Firmware Server Path
P192 =

# Config Server Path
P237 =

# Firmware File Prefix
P232 =

# Firmware File Postfix
P233 =

# Config File Prefix
P234 =

# Config File Postfix
P235 =

# Automatic Upgrade. 0 - No, 1 - Yes (checking every defined days). Default is No.
P194 = 0

# Check for new firmware every () minutes, unit is in minute, default is 7 days.
P193 = 10080

# Use firmware pre/postfix to determine if f/w is required
# 0 = Always Check for New Firmware 
# 1 = Check New Firmware only when F/W pre/suffix changes 
# 2 = Always Skip the Firmware Check
# For Firmware only.
P238 = 0

# Firmwae Key (AES 128, in Hexadecimal Representation) 
P242 =

# Authenticate Provision/Configuration File. 0 - No, 1 - Yes.
P240 = 0

#--------------------------------------------------------------

# For HT488, the following 5 fields are in the FXS Port Settings page
#
# Onhook Threshold. Default 800ms.
# <value=0>Hookflash OFF
# <value=6>600 ms
# <value=8>800 ms
# <value=10>1000 ms
# <value=12>1200 ms
P245 = 8

# FXS Impedence
#
# <value="0" > Default setting is "600 Ohm (North America)"
# <value=0>600 Ohm (North America)
# <value=1>900 Ohm
# <value=2>600 Ohm + 2.16uF
# <value=3>900 Ohm + 2.16uF
# <value=4>CTR21 (270 Ohm + 750 Ohm||150nF)
# <value=5>Australia/New Zealand #1 (220 Ohm + 820 Ohm||120nF)
# <value=6>Slovakia/Slovenia/South Africa (220 Ohm + 820 Ohm||115nF)
# <value=7>UK/New Zealand #2 (370 Ohm + 620 Ohm||310nF)
P86 = 0

# Caller ID Scheme
#
# <value="0">current setting is "Bellcore"
# <value=0>Bellcore (North America)
# <value=1>ETSI-FSK (France, Germany, Norway, Taiwan, UK-CCA)
# <value=2>ETSI-DTMF (Finland, Sweden)
# <value=3>DTMF-Denmark
# <value=4>CID-Canada
# <value=5>DTMF-Sweden
# <value=6>DTMF-Brazil
P200 = 0

# Onhook Voltage
#
# <value="3">current setting is "48V"
# <value=1>18V
# <value=5>24V
# <value=2>36V
# <value=3>48V
# <value=4>51V
P206 = 2

# Polarity Reversal. 0 - No, 1 - Yes.
P205 = 0

# NTP Server
P30 = time.nist.gov

# Syslog feature for HT496/386 only
# Syslog Server (name of the server, max length is 64 charactors)
P207 = 

# Syslog Level (Default setting is NONE)
# 0 - NONE, 1 - DEBUG, 2 - INFO, 3 - WARNING, 4 - ERROR
P208 = 0

##############################################################################
# HandyTone 488/496/386 Port 1 (FXS) Account Settings.
##############################################################################

# SIP Server
P47 = sip.mycompany.com

# Outbound Proxy
P48 = proxy.mycompany.com

# SIP User ID
P35 = 8000

# Authentication ID
P36 = 8000

# Authentication password
P34 = 0000

# User Caller Name (John Doe)
P3 = 

# Use DNS SRV. 0 - No, 1 - Yes.
P103 = 

# User ID is phone number. 0 - no, 1 - yes
P63 = 0

# SIP Registration. 0 - no, 1 - yes
P31 = 1

# Unregister On Reboot. 0 - no, 1 - yes
P81 = 0

# Register Expiration (in minutes. default 1 hour, max 45 days)
P32 = 60

# Local SIP port (default 5060)
P40 = 5060

# Local RTP port (1024-65535, default 5004)
P39 = 5004 

# Use Random Port. 0 - no, 1 - yes
P78 = 0

# SIP Registration Failure Retry Wait Time. (in seconds. Between 1-3600, default is 20)
P138 = 20

# DTMF Payload Type
P79 = 101

# Send DTMF. 8 - in audio, 1 - via RTP, 2 - via SIP INFO, 11 - In Audio & RTP & SIP INFO
# 9 - In Audio & RTP, 10 - IN Audio & SIP INFO, 3 - RTP & SIP INFO
P73 = 8

# Send Flash Event (Flash will be sent as a DTMF event if set to Yes). 0 - no, 1 - yes
P74 = 0

# Enable Call Features,  0 - No, 1 - Yes.
P191 = 1

# Use Bell-style 3-way Conference. 0 - No, 1 - Yes.
P108 = 0

# Offhook Auto-Dial (User ID/extension to dial automatically when offhook)
P71 =

# Proxy-Require (A SIP extension to enable firewall penetration)
P197 =

# Disable Call-Waiting. 0 - No, 1 - Yes.
P91 = 0

# Disable Call Waiting Caller ID (CWCID). 0 - No, 1 - Yes.
P714 = 0

# NAT Traversal (STUN). 0 - Yes, 1 - No
P52 = 0

# No Key Entry Timeout. Default - 4 seconds.
P85 = 4

# Preferred Vocoder
# 0 - PCMU, 2 - G.726-32, 4 - G.723.1, 8 - PCMA, 18 - G.729A/B, 98 - iLBC

# First codec. 
P57 = 0

# Second codec. 
P58 = 8

# Third codec. 
P59 = 4

# Forth codec. 
P60 = 18

# Fifthth codec. 
P61 = 2

# Sixth codec. 
P62 = 98

# Voice Frames per TX (up to 10/20/32/64 frames for G711/G726/G723/other codecs respectively)
P37 = 2

# G723 rate. 0 - 6.3kbps encoding rate, 1 - 5.3kbps encoding rate
P49 = 0

# iLBC Frame Size. 0 - 20ms(default), 1 - 30ms.
P97 = 0

# iLBC payload type. Between 96 and 127, default is 97.
P96 = 97

# Silence Suppression. 0 - no, 1 - yes
P50 = 0

# FAX Mode. 0 - T.38 (Auto Detect), 1 - Pass Through
P228 = 0

# Early Dial (use "Yes" only if proxy supports 484 response). 0 - no, 1 - yes
P29 = 0

# Allow incoming SIP messages from SIP proxy only. 0 - No, 1 - Yes.
P243 = 0

# Allow outgoing call without Registration. 0 - No, 1 - Yes.
P109 = 0

# Dial Plan Prefix (dial plan prefix string)
P66 =

# Use # as Dial Key (if set to Yes, "#" will function as the Dial key). 0 - no, 1 - yes
P72 = 1

# SUBSCRIBE for MWI. Whether or not send SUBSCRIBE for Message Waiting Indication.  0 - No, 1 - Yes.
P99 = 0

# Send Anonymous (caller ID will be blocked if set to Yes). 0 - no, 1 - yes
P65 = 0

# Lock Keypad Update. (configuration update via keypad is disabled if set to Yes)
# 0 - No, 1 - Yes.
P88 = 0

# Refer-To Use Target Contact. 0 - no, 1 - yes
P135 = 0

# Special Feature. 100 - Standard, 102 - BroadSoft, 105 - Lucent FS5000 Simple Endpoint, 108 - CBCOM, 109 - RNK.
P198 = 100

# Volume Amplification
# TX 
# <value=1> +6dB
# <value=2> +4dB
# <value=3> +2dB
# <value=0> 0dB
# <value=4> -2dB
# <value=5> -4dB
# <value=6> -6dB
P247 = 0 

# RX 
# <value=1> +6dB
# <value=2> +4dB
# <value=3> +2dB
# <value=0> 0dB
# <value=4> -2dB
# <value=5> -4dB
# <value=6> -6dB
P249 = 0

# Disable Line Echo Canceller (LEC). 0 - no, 1 - yes
P824 = 0

##############################################################################
# HandyTone 488/496/386 Port 2 (FXO/FXS) Account Settings.
##############################################################################

# SIP Server
P747 = 

# Outbound Proxy
P748 = 

# SIP User ID
P735 = 

# Authentication ID
P736 = 

# Authentication password
P734 = 

# User Caller Name
P703 = 

# Use DNS SRV. 0 - No, 1 - Yes.
P702 = 0

# User ID is phone number. 0 - no, 1 - yes
P763 = 0

# SIP Registration. 0 - no, 1 - yes
P731 = 1

# Unregister On Reboot. 0 - no, 1 - yes
P752 = 0

# Register Expiration (in minutes. default 1 hour, max 45 days)
P732 = 60

# Local SIP port (default 5062)
P740 = 5062

# Local RTP port (1024-65535, default 5008)
P739 = 5008

# Use Random Port. 0 - no, 1 - yes
P778 = 0

# SIP Registration Failure Retry Wait Time. (in seconds. Between 1-3600, default is 20)
P471 = 20

# DTMF Payload Type
P779 = 101
  
# Send DTMF. 8 - in audio, 1 - via RTP, 2 - via SIP INFO, - In Audio & RTP & SIP INFO
# In Audio & RTP - IN Audio & SIP INFO - RTP & SIP INFO
P773 = 8

# Send Flash Event (Flash will be sent as a DTMF event if set to Yes). 0 - no, 1 - yes
P774 = 0

# Enable call features. 0 - No, 1 - Yes. 
# For HT496/386 only
P751 = 1

# Use Bell-style 3-way Conference. 0 - No, 1 - Yes.
P711 = 0

# Offhook Auto-Dial (User ID/extension to dial automatically when offhook)
# For HT496/386 only
P771 =

# Proxy-Require (A SIP extension to enable firewall penetration)
P792 =

# Disable Call-Waiting. 0 - No, 1 - Yes.
# For HT496/386 only
P791 = 0

# Disable Call Waiting Caller ID (CWCID). 0 - No, 1 - Yes.
# For HT496/386 only
P823 = 0

# NAT Traversal (STUN). 0 - Yes, 1 - No
P730 = 0

# No Key Entry Timeout. Default - 4 seconds.
P292 = 4

# Preferred Vocoder
# 0 - PCMU, 2 - G.726-32, 4 - G.723.1, 8 - PCMA, 18 - G.729A/B, 98 - iLBC

# First codec. 
P757 = 0

# Second codec. 
P758 = 8

# Third codec. 
P759 = 4

# Forth codec. 
P760 = 18

# Fifth codec. 
P761 = 2

# Sixth codec. 
P762 = 98

# Voice Frames per TX (up to 10/20/32/64 frames for G711/G726/G723/other codecs respectively)
P737 = 2

# G723 rate. 0 - 6.3kbps encoding rate, 1 - 5.3kbps encoding rate
P749 = 0

# iLBC payload type. Between 96 and 127, default is 97.
P704 = 97

# iLBC Frame Size. 0 - 20ms(default), 1 - 30ms.
P705 = 0

# Silence Suppression. 0 - no, 1 - yes
P750 = 0

# FAX Mode. 0 - T.38 (Auto Detect), 1 - Pass Through
# For HT496/386 only
P710 = 0

# Early Dial (use "Yes" only if proxy supports 484 response). 0 - no, 1 - yes
P729 = 0

# Allow incoming SIP messages from SIP proxy only. 0 - No, 1 - Yes.
P743 = 0

# Allow outgoing call without Registration. 0 - No, 1 - Yes.
P813 = 0

# Dial Plan Prefix (dial plan prefix string)
P766 =

# Use # as Dial Key (if set to Yes, "#" will function as the Dial key). 0 - no, 1 - yes
P772 = 1

# SUBSCRIBE for MWI. Whether or not send SUBSCRIBE for Message Waiting Indication.  0 - No, 1 - Yes.
# For HT496/386 only
P709 = 0

# Send Anonymous (caller ID will be blocked if set to Yes). 0 - no, 1 - yes
P765 = 0

# Refer-To Use Target Contact. 0 - no, 1 - yes
P769 = 0

# Special Feature. 100 - Standard, 102 - BroadSoft, 105 - Lucent FS5000 Simple Endpoint, 108 - CBCOM, 109 - RNK.
# 107 - Route Access Code to PSTN.
P767 = 100

# Volume Amplification
# TX 
# <value=1> +6dB
# <value=2> +4dB
# <value=3> +2dB
# <value=0> 0dB
# <value=4> -2dB
# <value=5> -4dB
# <value=6> -6dB
P248 = 0 

# RX 
# <value=1> +6dB
# <value=2> +4dB
# <value=3> +2dB
# <value=0> 0dB
# <value=4> -2dB
# <value=5> -4dB
# <value=6> -6dB
P250 = 0

# Disable Line Echo Canceller (LEC). 0 - no, 1 - yes
P825 = 0

#--------------------------------------------------------------------
# The following 6 fields are for HT488 FXO Port only
#--------------------------------------------------------------------
# PSTN AC Termination Impedance
#
#  <value=0 selected >600 Ohm (North America)
#  <value=1          >900 Ohm</option>
#  <value=2          >270 Ohm + (750 Ohm || 150 nF) and 275 Ohm + (780 Ohm || 150 nF)
#  <value=3          >220 Ohm + (820 Ohm || 120 nF) and 220 Ohm + (820 Ohm || 115 nF)
#  <value=4          >370 Ohm + (620 Ohm || 310 nF)
#  <value=5          >320 Ohm + (1050 Ohm || 230 nF))
#  <value=6          >370 Ohm + (820 Ohm || 110 nF)
#  <value=7          >275 Ohm + (780 Ohm || 150 nF)
#  <value=8          >120 Ohm + (820 Ohm || 110 nF)
#  <value=9          >350 Ohm + (1000 Ohm || 210 nF)
#  <value=10         >0  Ohm + (900 Ohm || 30 nF)
#  <value=11         >600 Ohm + 2.16 uF
#  <value=12         >900 Ohm + 1 uF
#  <value=13         >900 Ohm + 2.16 uF
#  <value=14         >600 Ohm + 1 uF
#  <value=15         >Global complex impedance
P800 = 0

# Enable PSTN Disconnect Tone Detection. 0 - No, 1 - Yes.
# If enabled, following tone and cadence are used as disconnect signal.
P712 = 0

# PSTN Disconnect Tone. 0 - inactive, default is 480Hz and 620Hz.
# Frequency f1
P801 = 480
# Frequency f2
P802 = 620

# PSTN Disconnect Tone Cadence. 0 - Disabled. Default is 0.
# Choice 1, On
P804 = 0
# Choice 1, Off
P805 = 0
# Choice 2, On
P806 = 0
# Choice 2, Off
P807 = 0
# Choice 3, On
P808 = 0
# Choice 3, Off
P809 = 0

# PSTN Silence Timeout. In seconds, terminate call after long silence detected.
# default is 60 sec, max 65536.
P810 = 60

# Enable Current Disconnect. 0 - No, 1 - Yes.
P768 = 1

# If current disconnect enabled, use threshold.
# Duration of power lose as disconnect, default 100ms, min 50ms
P764 = 100

# Min Delay Before Dial. Min delay before dial after offhook, default 100ms, normally 100~800ms, min 100ms
P713 = 100

##############################################################################
# Audible Tones.
##############################################################################

#-----------------------------------------------------------------------------
# FXS Port1
#-----------------------------------------------------------------------------

##### Call Progress Tones #####
#
### Dial Tone ###
# Frequency 1 (Hz)
P1820 = 350
# Frequency 2 (Hz)
P1840 = 440
# ON (x 10ms)
P1860 = 0
# OFF (x 10ms)
P1880 = 0

### Recall Dial Tone ###
# Frequency 1 (Hz)
P1821 = 350
# Frequency 2 (Hz)
P1841 = 440
# ON (x 10ms)
P1861 = 10
# OFF (x 10ms)
P1881 = 10

### Message Waiting Tone ###
# Frequency 1 (Hz)
P1822 = 350
# Frequency 2 (Hz)
P1842 = 440
# ON (x 10ms)
P1862 = 10
# OFF (x 10ms)
P1882 = 10

### Confirmation Tone ###
# Frequency 1 (Hz)
P1823 = 350
# Frequency 2 (Hz)
P1843 = 440
# ON (x 10ms)
P1863 = 10
# OFF (x 10ms)
P1883 = 10

### Audiable Ringing ###
# Frequency 1 (Hz)
P1824 = 440
# Frequency 2 (Hz)
P1844 = 480
# ON (x 10ms)
P1864 = 200
# OFF (x 10ms)
P1884 = 400

### Busy Tone ###
# Frequency 1 (Hz)
P1825 = 480
# Frequency 2 (Hz)
P1845 = 620
# ON (x 10ms)
P1865 = 50
# OFF (x 10ms)
P1885 = 50

### Reorder Tone ###
# Frequency 1 (Hz)
P1826 = 480
# Frequency 2 (Hz)
P1846 = 620
# ON (x 10ms)
P1866 = 25
# OFF (x 10ms)
P1886 = 25

### Receiver offhook ###
# Frequency 1 (Hz)
P1827 = 1400
# Frequency 2 (Hz)
P1847 = 2600
# ON (x 10ms)
P1867 = 10
# OFF (x 10ms)
P1887 = 10

##### Distinct Ring Tones #####
#
# For HT496 only
#
### Ring1 ###
# Frequency 1 (Hz)
P1828 = 440
# Frequency 2 (Hz)
P1848 = 440
# ON (x 10ms)
P1868 = 100
# OFF (x 10ms)
P1888 = 100

### Ring2 ###
# Frequency 1 (Hz)
P1829 = 440
# Frequency 2 (Hz)
P1849 = 440
# ON (x 10ms)
P1869 = 100
# OFF (x 10ms)
P1889 = 100
 
### Ring3 ###
# Frequency 1 (Hz)
P1830 = 440
# Frequency 2 (Hz)
P1850 = 440
# ON (x 10ms)
P1870 = 100
# OFF (x 10ms)
P1890 = 100

### Ring4 ###
# Frequency 1 (Hz)
P1831 = 440
# Frequency 2 (Hz)
P1851 = 440
# ON (x 10ms)
P1871 = 100
# OFF (x 10ms)
P1891 = 100

### Ring5 ###
# Frequency 1 (Hz)
P1832 = 440
# Frequency 2 (Hz)
P1852 = 440
# ON (x 10ms)
P1872 = 100
# OFF (x 10ms)
P1892 = 100

### Ring6 ###
# Frequency 1 (Hz)
P1833 = 440
# Frequency 2 (Hz)
P1853 = 440
# ON (x 10ms)
P1873 = 100
# OFF (x 10ms)
P1893 = 100

### Ring7 ###
# Frequency 1 (Hz)
P1834 = 20
# Frequency 2 (Hz)
P1854 = 20
# ON (x 10ms)
P1874 = 80
# OFF (x 10ms)
P1894 = 40

### Ring8 ###
# Frequency 1 (Hz)
P1835 = 20
# Frequency 2 (Hz)
P1855 = 20
# ON (x 10ms)
P1875 = 40
# OFF (x 10ms)
P1895 = 20

### Ring9 ###
# Frequency 1 (Hz)
P1836 = 20
# Frequency 2 (Hz)
P1856 = 20
# ON (x 10ms)
P1876 = 30
# OFF (x 10ms)
P1896 = 20

### Ring10 ###
# Frequency 1 (Hz)
P1837 = 20
# Frequency 2 (Hz)
P1857 = 20
# ON (x 10ms)
P1877 = 50
# OFF (x 10ms)
P1897 = 800

### Ring11 ###
# Frequency 1 (Hz)
P1838 = 20
# Frequency 2 (Hz)
P1858 = 20
# ON (x 10ms)
P1878 = 200
# OFF (x 10ms)
P1898 = 400

### Ring12 ###
# Frequency 1 (Hz)
P1839 = 20
# Frequency 2 (Hz)
P1859 = 20
# ON (x 10ms)
P1879 = 200
# OFF (x 10ms)
P1899 = 400

#-----------------------------------------------------------------------------
# FXS Port2 (HT496/HT386 only)
#-----------------------------------------------------------------------------

##### Call Progress Tones #####
#
### Dial Tone ###
# Frequency 1 (Hz)
P2820 = 350
# Frequency 2 (Hz)
P2840 = 440
# ON (x 10ms)
P2860 = 0
# OFF (x 10ms)
P2880 = 0

### Recall Dial Tone ###
# Frequency 1 (Hz)
P2821 = 350
# Frequency 2 (Hz)
P2841 = 440
# ON (x 10ms)
P2861 = 10
# OFF (x 10ms)
P2881 = 10

### Message Waiting Tone ###
# Frequency 1 (Hz)
P2822 = 350
# Frequency 2 (Hz)
P2842 = 440
# ON (x 10ms)
P2862 = 10
# OFF (x 10ms)
P2882 = 10

### Confirmation Tone ###
# Frequency 1 (Hz)
P2823 = 350
# Frequency 2 (Hz)
P2843 = 440
# ON (x 10ms)
P2863 = 10
# OFF (x 10ms)
P2883 = 10

### Audiable Ringing ###
# Frequency 1 (Hz)
P2824 = 440
# Frequency 2 (Hz)
P2844 = 480
# ON (x 10ms)
P2864 = 200
# OFF (x 10ms)
P2884 = 400

### Busy Tone ###
# Frequency 1 (Hz)
P2825 = 480
# Frequency 2 (Hz)
P2845 = 620
# ON (x 10ms)
P2865 = 50
# OFF (x 10ms)
P2885 = 50

### Reorder Tone ###
# Frequency 1 (Hz)
P2826 = 480
# Frequency 2 (Hz)
P2846 = 620
# ON (x 10ms)
P2866 = 25
# OFF (x 10ms)
P2886 = 25

### Receiver offhook ###
# Frequency 1 (Hz)
P2827 = 1400
# Frequency 2 (Hz)
P2847 = 2600
# ON (x 10ms)
P2867 = 10
# OFF (x 10ms)
P2887 = 10

##### Distinct Ring Tones #####
#
# For HT496 only
#
### Ring1 ###
# Frequency 1 (Hz)
P2828 = 440
# Frequency 2 (Hz)
P2848 = 440
# ON (x 10ms)
P2868 = 100
# OFF (x 10ms)
P2888 = 100

### Ring2 ###
# Frequency 1 (Hz)
P2829 = 440
# Frequency 2 (Hz)
P2849 = 440
# ON (x 10ms)
P2869 = 100
# OFF (x 10ms)
P2889 = 100
 
### Ring3 ###
# Frequency 1 (Hz)
P2830 = 440
# Frequency 2 (Hz)
P2850 = 440
# ON (x 10ms)
P2870 = 100
# OFF (x 10ms)
P2890 = 100

### Ring4 ###
# Frequency 1 (Hz)
P2831 = 440
# Frequency 2 (Hz)
P2851 = 440
# ON (x 10ms)
P2871 = 100
# OFF (x 10ms)
P2891 = 100

### Ring5 ###
# Frequency 1 (Hz)
P2832 = 440
# Frequency 2 (Hz)
P2852 = 440
# ON (x 10ms)
P2872 = 100
# OFF (x 10ms)
P2892 = 100

### Ring6 ###
# Frequency 1 (Hz)
P2833 = 440
# Frequency 2 (Hz)
P2853 = 440
# ON (x 10ms)
P2873 = 100
# OFF (x 10ms)
P2893 = 100

### Ring7 ###
# Frequency 1 (Hz)
P2834 = 20
# Frequency 2 (Hz)
P2854 = 20
# ON (x 10ms)
P2874 = 80
# OFF (x 10ms)
P2894 = 40

### Ring8 ###
# Frequency 1 (Hz)
P2835 = 20
# Frequency 2 (Hz)
P2855 = 20
# ON (x 10ms)
P2875 = 40
# OFF (x 10ms)
P2895 = 20

### Ring9 ###
# Frequency 1 (Hz)
P2836 = 20
# Frequency 2 (Hz)
P2856 = 20
# ON (x 10ms)
P2876 = 30
# OFF (x 10ms)
P2896 = 20

### Ring10 ###
# Frequency 1 (Hz)
P2837 = 20
# Frequency 2 (Hz)
P2857 = 20
# ON (x 10ms)
P2877 = 50
# OFF (x 10ms)
P2897 = 800

### Ring11 ###
# Frequency 1 (Hz)
P2838 = 20
# Frequency 2 (Hz)
P2858 = 20
# ON (x 10ms)
P2878 = 200
# OFF (x 10ms)
P2898 = 400

### Ring12 ###
# Frequency 1 (Hz)
P2839 = 20
# Frequency 2 (Hz)
P2859 = 20
# ON (x 10ms)
P2879 = 200
# OFF (x 10ms)
P2899 = 400

#################################################################################
## End User Settings. Please do not edit this section.
#################################################################################

# End User Password
#P196 = 123

# Web Port. Device internal HTTP server port number. Default is 80.
P901 = 80

# DHCP support. 0 - yes, 1 - no
#P8 = 0

# Host name, DHCP option 12. Max length allowed is 32 bytes.
P146 =

# Domain name, DHCP option 15. Max length allowed is 32 bytes.
P147 =

# Vendor Class ID, DHCP option 60. Max length allowed is 32 bytes.
P148 = 

# PPPoE support. PPPoE user ID
#P82 =

# PPPoE password
#P83 =

# PPPoE Service Name
#P269 =

# IP Address. Ignore if DHCP or PPPoE is used
#P9 = 
#P10 = 
#P11 = 
#P12 = 

# Subnet mask. Ignore if DHCP or PPPoE is used
#P13 = 255
#P14 = 255
#P15 = 255
#P16 = 0

# Router. Ignore if DHCP or PPPoE is used
#P17 = 
#P18 = 
#P19 = 
#P20 = 

# Preferred DNS server.  (if specified).
#P92 = 
#P93 = 
#P94 = 
#P95 = 

# DNS 1. Ignore if DHCP or PPPoE is used
#P21 = 
#P22 = 
#P23 = 
#P24 = 

# DNS 2. Ignore if DHCP or PPPoE is used
#P25 = 0
#P26 = 0
#P27 = 0
#P28 = 0

# Time Zone. Offset in minutes to GMT
#P64 = 420

# Daylight Savings Time. 0 - no, 1 - yes
#P75 = 0

# Optional Rule. Daylight Saving rule.
P246 = 4,1,7,2,0;10,-1,7,2,0;60

# PSTN Access Code.   Default = *00
# HT488/386 only
#P195 = 

#------------------------------------------------------------------------
# HandyTone 488/496 End User Specific NAT Settings.
#------------------------------------------------------------------------

# Device Mode. 0 - NAT Router, 1 - Bridge. Default is 0.
# HT496 only
#P231 = 0

# WAN side http access.  0 - Disable(default), 1 - Yes.
# For HT488/496 only
P190 = 0

# Reply to ICMP on WAN port (Unit will not respond to PING from WAN side if set to No)
# 0 - No, 1 - Yes.
P189 = 0

#Cloned WAN MAC Address.
#P115 =
#P116 =
#P117 =
#P118 =
#P119 =
#P120 =

#LAN Subnet Mask.  Example: 255.255.255.224
#P110 = 

#LAN Base/Gateway/Router IP for the LAN port, default is 192.168.2.1.
#P111 = 

#DHCP IP Lease Time, in units of hours, default is 120 hours or 5 days.
#P112 = 120

#DMZ IP.
#P113 =

#-----------------------------------------------------------
# Port Forwarding Settings.
#-----------------------------------------------------------

#############  Choice 1 ####################################
# WAN Port
P150 =
# LAN IP
P158 =
# LAN Port
P166 =
# Protocol.  0 - UDP Only, 1 - TCP Only, 2 - TCP and UDP.
P174 =
#############  Choice 2 ####################################
# WAN Port
P151 =
# LAN IP
P159 =
# LAN Port
P167 =
# Protocol.  0 - UDP Only, 1 - TCP Only, 2 - TCP and UDP.
P175 =
#############  Choice 3 ####################################
# WAN Port
P152 =
# LAN IP
P160 =
# LAN Port
P168 =
# Protocol.  0 - UDP Only, 1 - TCP Only, 2 - TCP and UDP.
P176 =
#############  Choice 4 ####################################
# WAN Port
P153 =
# LAN IP
P161 =
# LAN Port
P169 =
# Protocol.  0 - UDP Only, 1 - TCP Only, 2 - TCP and UDP.
P177 =
#############  Choice 5 ####################################
# WAN Port
P154 =
# LAN IP
P162 =
# LAN Port
P170 =
# Protocol.  0 - UDP Only, 1 - TCP Only, 2 - TCP and UDP.
P178 =
#############  Choice 6 ####################################
# WAN Port
P155 =
# LAN IP
P163 =
# LAN Port
P171 =
# Protocol.  0 - UDP Only, 1 - TCP Only, 2 - TCP and UDP.
P179 =
#############  Choice 7 ####################################
# WAN Port
P156 =
# LAN IP
P164 =
# LAN Port
P172 =
# Protocol.  0 - UDP Only, 1 - TCP Only, 2 - TCP and UDP.
P180 =
#############  Choice 8 ####################################
# WAN Port
P157 = 
# LAN IP
P165 = 
# LAN Port
P173 = 
# Protocol.  0 - UDP Only, 1 - TCP Only, 2 - TCP and UDP.
P181 = 

#-------------------------------------------------------------------------------
# HandyTone 488 Specific End User Settings. 
#-------------------------------------------------------------------------------

# Number of Rings (Number of FXS phone rings for FXO incoming PSTN calls before bridgeing to VoIP)
# Default is 0.
#P798 = 0

# PIN for PSTN Calls
#P794 = 

# PIN for VoIP Calls
#P795 =

# Route Call to PSTN (outbound calls will be routed to PSTN port when dialed digits match one of the following)
#P780 =
#P781 =
#P782 =
#P783 =
#P784 =
#P785 =
#P786 =
#P787 =
#P788 =
#P789 =

# Forward to PSTN (VoIP calls will be forwarded to the specified PSTN number) 
#P796 =

# Forward to VoIP (PSTN calls will be forwarded to the specified VoIP number)
#P797 =

# FXO One Stage Dialing. 0 - No, 1 - Yes
# Default No. SIP UserID is used as PSTN number if set to Yes.
#P770 = 0