################################################################################################ ## Configuration template for GXV-3000 firmware version 1.1.3.14 ################################################################################################ ############################################################################## ## Advanced/System-wide Options ############################################################################## # Password for configuration file authentication P1 = # Admin password for web interface, max. length is 30 P2 = sarabon # G.723 rate: 0 - 6.3kbps encoding rate, 1 - 5.3kbps encoding rate P49 = P86 = 6 # Silence Suppression. 0 - no, 1 - yes P50 = 0 # Voice Frames per TX (up to 10/20/32/64 frames for G711/G726/G723/other codecs respectively) P37 = 2 # Video frame rate: default - 15 P904 = 15 # Video bit rate (kbps): default is 128 P905 = 128 # Video Packet Size: maxlength = 4, from 100~1400, default is 1400 P927 = 800 # Video Rate Control. 0 - Frame, 1 - TMN8 P924 = # Video Frame Skipping. 0 - no, 1 - yes P925 = 0 # Sharpening Filter. (0-9, 0 means disabled, default is 5) P938 = 5 # Brightening Filter. (0-9, 0 means disabled, default is 5) P939 = 5 # Tone Remapping Filter. (0-255, 0 means disabled, default is 32) P948 = 32 # Enable Video Surveillance. Turn phone into video surveillance camera if set to 1, YES. Default=No, 0. P928 = 0 # Surveillance RTSP Port. Video Surveillance data stream port, default is 554. P929 = 554 # Streaming RTSP Server P953 = # Streaming RTSP User ID P954 = # Streaming RTSP Password P955 = # Layer 3 QoS (IP Diff-Serv or Precedence value for RTP) P38 = 0 # Layer 2 QoS. 802.1Q/VLAN Tag (VLAN classification for RTP) P51 = 0 # Layer 2 QoS. 802.1p priority value (0 - 7) P87 = 0 # No Key Entry Timeout. Default - 4 seconds. P85 = 4 # Use # as Dial Key. 0 - no, 1 - yes P72 = 1 # Local RTP port (1024-65535, default 5004) P39 = 5004 # Use Random Port. 0 - no, 1 - yes P78 = 0 # Keep-alive interval (in seconds. default 20 seconds) P84 = 60 # Use NAT IP. This will enable our SIP client to use this IP in the SIP message. Example 64.3.153.50. P101 = # STUN server P76 = stun.mycompany.com #------------------------------------------------------------- # Firmware Upgrade #------------------------------------------------------------- # Firmware Upgrade. 0 - TFTP Upgrade, 1 - HTTP Upgrade. P212 = 0 # Firmware Server Path # P192 = fm.grandstream.com/gs P192 = 192.168.45.5 # Config Server Path # P237 = fm.grandstream.com/gs P237 = 192.168.45.5 # Firmware File Prefix P232 = # Firmware File Postfix P233 = # Config File Prefix P234 = # Config File Postfix P235 = # Allow DHCP Option 66 to override server. 0 - No, 1 - Yes. Default is Yes. # When set to Yes(1), it will override the configured provision path and method. P145 = 1 # Automatic Upgrade. 0 - No, 1 - Yes. Default is No. P194 = 0 # Check for new firmware every () minutes, unit is in minute, minimnu 60 minutes, default is 7 days. P193 = 10080 # Use firmware pre/postfix to determine if f/w is required # 0 = Always Check for New Firmware # 1 = Check New Firmware only when F/W pre/suffix changes # 2 = Always Skip the Firmware Check P238 = 0 # Authenticate Conf File P240 = 0 # Enable Screen Saver Download # 0 = No # 1 = YES, HTTP # 2 = YES, TFTP P933 = 0 # Screen Saver Download Server Path P934 = # Enable Phonebook XML Download # 0 = No # 1 = YES, HTTP # 2 = YES, TFTP P330 = 0 # Phonebook XML Server Path # This is a string of up to 128 characters that should contain a path to the XML file. # It MUST be in the host/path format. For example: "directory.grandstream.com/engineering" P331 = # Remove Manually-edited entries on Download # 0 - No, 1 - Yes P333 = 0 # Enable Network Screen Saver # 0 - No # 1 - YES, HTTP P943 = 0 # Network Screen Saver Server Path P942 = # Enable Weather Forecast # 0 - No # 1 - YES, HTTP P945 = 0 # Weather Forecast Server Path P944 = # Enable Headline News # 0 - No # 1 - YES, HTTP P947 = 0 # Headline News RSS Server Path P946 = # Offhook Auto Dial P71 = # DTMF Payload Type P79 = 101 # Syslog Server (name of the server, max length is 64 charactors) P207 = # Syslog Level (Default setting is NONE) # 0 - NONE, 1 - DEBUG, 2 - INFO, 3 - WARNING, 4 - ERROR P208 = 0 # NTP Server P30 = ntp.bring.out.ba # Allow DHCP Option 42 to override NTP server. 0 - No, 1 - Yes. Default is No. # When set to Yes(1), it will override the configured NTP server. P144 = 0 # Distinctive Ring Tone # Use custom ring tone 1 if incoming caller ID is the following: P105 = # Use custom ring tone 2 if incoming caller ID is the following: P106 = # Use custom ring tone 3 if incoming caller ID is the following: P107 = # System Ring Tone: input type = text, maxlength=64 size=30 P345 = f1=440,f2=480,c=200/400; #------------------------------------------------------------ #Call Progress Tones: input type=text, maxlength=64, size=30 #------------------------------------------------------------ # Dial Tone P343 = f1=350,f2=440; # Message Waiting Tone P344 = f1=350,f2=440,c=10/10; # Ring Back Tone P346 = f1=440,f2=480,c=200/400; # Call-Waiting Tone P347 = f1=440,f2=440,c=25/525; # Busy Tone P348 = f1=480,f2=620,c=50/50; # Reorder Tone P349 = f1=480,f2=620,c=25/25; # Start Browser On Boot: 0 - no (default), 1 - yes P950 = 0 # Enable Browser Toolbar: 0 - no (default), 1 - yes P951 = 0 # Browser Home Page, maxlength=64, default = about:/start.htm P952 = about:/start.htm # Disable Call Waiting. 0 - no, 1 - yes P91 = 0 # Disable Call Waiting Tone: 0 - no (default), 1 - yes P186 = 0 # Disable Direct IP Call. 0 - no, 1 - yes P277 = 0 # Use Quick IP-call mode: 0 - no, 1 - yes. Default is No. P184 = 0 # Allow Media Loopback. 0 - no, 1 - yes P278 = 0 # Lock Keypad Update. 0 - no, 1 - yes P88 = 0 # Display Language. 0 - English, 1 - Downloaded Language, 2 - Chinese P342 = 0 # language file postfix P399 = #################################################################### # Primary Account (Account 1) Settings #################################################################### # Account Active (In Use). 0 - no, 1 - yes P271 = 1 # Account Name P270 = 20 # SIP Server: max. length = 96 P47 = asterisk.bring.out.ba # Outbound Proxy P48 = asterisk.bring.out.ba # SIP User ID P35 = 20 # Authenticate ID P36 = 20 # Authenticate password P34 = sarabon # Display Name (John Doe) P3 = hernad dish # Use DNS SRV. 0 - No, 1 - Yes. P103 = 0 # SIP User ID is phone number. 0 - no, 1 - yes P63 = 0 # SIP Registration. 0 - no, 1 - yes P31 = 1 # Unregister On Reboot. 0 - no, 1 - yes P81 = 1 # Register Expiration (in minutes. default 1 hour, max 45 days) P32 = 10 # SIP Registration Failure Retry Wait Time (in seconds. Between 1-3600, default is 20) P138 = 20 # Local SIP port (default 5060) P40 = 5060 # NAT Traversal (STUN). 0 - yes, 1 - no, 2 - No, but send keep-alive P52 = 1 # SUBSCRIBE for MWI. (Whether or not send SUBSCRIBE for Message Waiting Indication) 0 - No, 1 - Yes. P99 = 0 # Proxy-Require (A SIP extension to enable firewall penetration) P197 = # SIP Compact Header. 0 - no, 1 - yes P289 = 0 # Voice Mail UserID (User ID/extension for 3rd party voice mail system) P33 = # Send DTMF. 8 - in audio, 1 - via RTP, 2 - via SIP INFO, 11 - In Audio & RTP & SIP INFO # 9 - In Audio & RTP, 10 - IN Audio & SIP INFO, 3 - RTP & SIP INFO P73 = 8 # Early Dial (use "Yes" only if proxy supports 484 response). 0 - no, 1 - yes P29 = 0 # Dial Plan Prefix (dial plan prefix string) P66 = # Dial Plan. Maxlength = 128 character. Defalut is allow all, {x.}, see user manual P290 ={x+} # Delayed Call Forward Wait Time. Default is 20 seconds, maxlength = 5 P139 = 20 # Enable Call Features. 0 - no, 1 - yes P191 = 1 # Session Expiration (in seconds. default 180 seconds. Allowed value: 90-65535) P260 = 180 # Minimum SE (in seconds. default 90 seconds, must be lower than or equal to P260) P261 = 90 # Caller Request Timer (Request for timer when calling) 0 - no, 1 - yes P262 = 0 # Callee Request Timer (Request for timer when called. i.e. if remote party supports timer but did not request for one) 0 - no, 1 - yes P263 = 0 # Force Timer (Still use timer when remote party does not support timer) 0 - no, 1 - yes P264 = 0 # UAC Specify Refresher. 0 - omit, 1 - UAC, 2 - UAS P266 = 0 # UAS Specify Refresher. 1 - UAC, 2 - UAS P267 = 1 # Force INVITE (Always refresh with INVITE instead of UPDATE even when remote party supports UPDATE) 0 - no, 1 - yes P265 = 0 # Enable 100rel. 0 - no, 1 - yes P272 = 0 # Account Ring Tone. 0 - system ring tone, 1 - custom ring tone 1, 2 - custom ring tone 2, 3 - custom ring tone 3. P104 = 0 # Send Anonymous. 0 - no, 1 - yes (caller ID will be blocked if set to Yes) P65 = 0 # Anonymous Call Rejection: 0 - no (default), 1 - yes P129 = 0 # Refer-To Uses Target Contact: 0 - no (default), 1 - yes P135 = 0 # Auto Answer. 0 - no, 1 - yes, 2 - Intercom/Paging P90 = 0 # Preferred Vocoder # 0 - PCMU, 2 - G.726-32, 3 - GSM, 4 - G.723.1, 8 - PCMA, # 9 - G.722, 18 - G.729A/B, 98 - iLBC # Currently only PCMU/PCMA, GSM, G.723, G.729 and G.726-32 supported, will add others in the future # First codec. P57 = 0 # Second codec. P58 = 8 # Third codec. P59 = 4 # Forth codec. P60 = 18 # Fifth codec. P61 = 3 # Sixth codec. P62 = 2 # Seventh codec. P46 = 0 # Eighth codec. P98 = 0 # Preferred Video Coder: 99 - H.264, 34 - H.263, 103 - H.263+ (1998) # Choice 1 P295 = 99 # Choice 2 P296 = 34 # Jitter Delay: 0 - Medium, 1 - Low, 2 - High P300 = 0 # Enable Video: 0 - No, 1 - Yes P292 = 1 # H.264 payload type: between 96 ~ 127, default = 99 P293 = 99 # H.263+ (1998) payload type: between 96 ~ 127, default = 103 P350 = 103 # SRTP Mode: Disabled - 0, Enabled but not forced - 1, Enabled and forced - 2 P183 = 0 # Special Feature. 100 - Standard, 101 - Nortel MCS, 102 - BroadSoft, 104 - Sonus, 108 - CBCOM, 109 - RNK P198 = 100 ######################################################################## # SIP Account 2 Settings ######################################################################## # Account Active (In Use). 0 - no, 1 - yes P401 = 0 #Account Name P417 = # SIP Server P402 = # Outbound Proxy Server P403 = # Account 2 SIP User ID P404 = # Authenticate ID P405 = # Authenticate Password P406 = # Display Name (John Doe) P407 = # Use DNS SRV. 0 - No, 1 - Yes. P408 = 0 # User ID is phone number; "user=phone". 0 - no, 1 - yes P409 = 0 # SIP Registration. 0 - no, 1 - yes P410 = 1 # Unregister on Reboot. 0 - no, 1 - yes P411 = 0 # Register Expiration (in minutes. default 1 hour, max 45 days) P412 = 60 # Registration Retry Wait Time (in seconds. Between 1-3600, default is 20) P471 = 20 # Local SIP port (default 5062) P413 = 5062 # NAT Traversal. 0 - yes, 1 - no, 2 - No, but send keep-alive P414 = 0 # Subscribe MWI. (Whether or not send SUBSCRIBE for Message Waiting Indication) 0 - No, 1 - Yes. P415 = 0 # Proxy Require P418 = # SIP Compact Header. 0 - no, 1 - yes P472 = 0 # Voice Mail UserID (User ID/extension for 3rd party voice mail system) P426 = # Send DTMF. 8 - in audio, 1 - via RTP, 2 - via SIP INFO, 11 - In Audio & RTP & SIP INFO # 9 - In Audio & RTP, 10 - IN Audio & SIP INFO, 3 - RTP & SIP INFO P416 = 8 # Early Dial. 0 - no, 1 - yes P422 = 0 # Dial Plan Prefix P419 = # Dial Plan. Maxlength = 128, default is allow all {x.} P459 = {x.} # Delayed Call Forward Wait Time. Default is 20 seconds, maxlength = 5 P470 = 20 # Enable Call Features. 0 - no, 1 - yes. P420 = 1 # Session Expiration (in seconds. default 180 seconds. Allowed value: 90-65535) P434 = 180 # Minimum SE (in seconds. default 90 seconds, must be lower than or equal to P260) P427 = 90 # Caller Request Timer (Request for timer when calling) 0 - no, 1 - yes P428 = 0 # Callee Request Timer (Request for timer when called. i.e. if remote party supports timer but did not request for one) 0 - no, 1 - yes P429 = 0 # Force Timer (Still use timer when remote party does not support timer) 0 - no, 1 - yes P430 = 0 # UAC Specify Refresher. 0 - omit, 1 - UAC, 2 - UAS P432 = 0 # UAS Specify Refresher. 1 - UAC, 2 - UAS P433 = 1 # Force INVITE (Always refresh with INVITE instead of UPDATE even when remote party supports UPDATE) 0 - no, 1 - yes P431 = 0 # Enable 100rel. 0 - no, 1 - yes P435 = 0 # Account Ring Tone. 0 - system ring tone, 1 - custom ring tone 1, 2 - custom ring tone 2, 3 - custom ring tone 3. P423 = 0 # Send Anonymous. 0 - no, 1 - yes ((caller ID will be blocked if set to Yes) P421 = 0 # Anonymous Call Rejection: 0 - no (default), 1 - yes P446 = 0 # Refer-To Uses Target Contact: 0 - no (default), 1 - yes P469 = 0 # Auto Answer. 0 - no, 1 - yes, 2 - Intercom/Paging P425 = 0 # Preferred Vocoder # 0 - PCMU, 2 - G.726-32, 3 - GSM, 4 - G.723.1, 8 - PCMA, # 9 - G.722, 18 - G.729A/B, 98 - iLBC # Currently only PCMU/PCMA, GSM, G.723, G.729 and G.726-32 supported, will add others in the future # First codec. P451 = 0 # Second codec. P452 = 8 # Third codec. P453 = 4 # Forth codec. P454 = 18 # Fifth codec. P455 = 3 # Sixth codec. P456 = 2 # Seventh codec. P457 = 0 # Eighth codec. P458 = 0 # Preferred Video Codec: 99 - H.264, 34 - H.263 103 - H.263+ (1998) # Choice 1 P464 = 99 # Choice 2 P465 = 34 # Jitter Delay: 0 - Medium, 1 - Low, 2 - High P467 = 0 # Enable Video: 0 - No, 1 - Yes P461 = 1 # H.264 payload type: between 96 ~ 127, default = 99 P462 = 99 # H.263+ (1998) payload type: between 96 ~ 127, default = 103 P473 = 103 # SRTP Mode: Disabled - 0, Enabled but not forced - 1, Enabled and forced - 2 P443 = 0 # Special Feature. 100 - Standard, 101 - Nortel MCS, 102 - BroadSoft, 104 - Sonus, 108 - CBCOM, 109 - RNK P424 = 100 ######################################################################## # SIP Account 3 Settings ######################################################################## # Account Active (In Use). 0 - no, 1 - yes P501 = 0 # Account Name P517 = # SIP Server P502 = # Outbound Proxy Server P503 = # SIP User ID P504 = # Authenticate ID P505 = # Authenticate Password P506 = # Display Name (John Doe) P507 = # Use DNS SRV. 0 - No, 1 - Yes. P508 = 0 # User ID is phone. "user=phone". 0 - no, 1 - yes P509 = 0 # SIP Registration. 0 - no, 1 - yes P510 = 1 # Unregister on Reboot. 0 - no, 1 - yes P511= 0 # Register Expiration (in minutes. default 1 hour, max 45 days) P512 = 60 # Registration Retry Wait Time (in seconds. Between 1-3600, default is 20) P571 = 20 # SIP Local port (default 5064) P513 = 5064 # NAT Traversal. 0 - yes, 1 - no, 2 - No, but send keep-alive P514 = # Subscribe MWI. (Whether or not send SUBSCRIBE for Message Waiting Indication) 0 - no, 1 - yes P515 = 0 # Proxy Require P518 = # SIP Compact Header. 0 - no, 1 - yes P572 = 0 # Voice Mail UserID (User ID/extension for 3rd party voice mail system) P526 = # Send DTMF. 8 - in audio, 1 - via RTP, 2 - via SIP INFO, 11 - In Audio & RTP & SIP INFO # 9 - In Audio & RTP, 10 - IN Audio & SIP INFO, 3 - RTP & SIP INFO P516 = 8 # Early Dial. 0 - no, 1 - yes P522 = 0 # Dial Plan Prefix P519 = # Dial Plan: Maxlength = 128, default is allow all {x.} P559 = {x.} # Delayed Call Forward Wait Time. Default is 20 seconds, maxlength = 5 P570 = 20 # Enable Call Features. 0 - no, 1 - yes. P520 = 1 # Session Expiration (in seconds. default 180 seconds. Allowed value: 90-65535) P534 = 180 # Minimum SE (in seconds. default 90 seconds, must be lower than or equal to P260) P527 = 90 # Caller Request Timer (Request for timer when calling) 0 - no, 1 - yes P528 = # Callee Request Timer (Request for timer when called. i.e. if remote party supports timer but did not request for one) 0 - no, 1 - yes P529 = # Force Timer (Still use timer when remote party does not support timer) 0 - no, 1 - yes P530 = # Force INVITE (Always refresh with INVITE instead of UPDATE even when remote party supports UPDATE) 0 - no, 1 - yes P531 = # UAC Specify Refresher. 0 - omit, 1 - UAC, 2 - UAS P532 = 0 # UAS Specify Refresher. 1 - UAC, 2 - UAS P533 = 1 # Enable 100rel. 0 - no, 1 - yes P535 = 0 # Account Ring Tone. 0 - system ring tone, 1 - custom ring tone 1, 2 - custom ring tone 2, 3 - custom ring tone 3. P523 = 0 # Send Anonymous (caller ID will be blocked if set to Yes). 0 - no, 1 - yes P521 = 0 # Anonymous Call Rejection: 0 - no (default), 1 - yes P546 = 0 # Refer-To Uses Target Contact: 0 - no (default), 1 - yes P569 = 0 # Auto Answer. 0 - no, 1 - yes, 2 - Intercom/Paging P525 = 0 # Preferred Vocoder # 0 - PCMU, 2 - G.726-32, 3 - GSM, 4 - G.723.1, 8 - PCMA, # 9 - G.722, 18 - G.729A/B, 98 - iLBC # Currently only PCMU/PCMA, GSM, G.723, G.729 and G.726-32 supported, will add others in the future # First codec. P551 = 0 # Second codec. P552 = 8 # Third codec. P553 = 4 # Forth codec. P554 = 18 # Fifth codec. P555 = 3 # Sixth codec. P556 = 2 # Seventh codec. P557 = 0 # Eighth codec. P558 = 0 # Preferred Video Codec: 99 - H.264, 34 - H.263, 103 - H.263+ (1998) # Choice 1 P564 = 99 # Choice 2 P565 = 34 # Jitter Delay: 0 - Medium, 1 - Low, 2 - High P567 = 0 # Enable Video: 0 - No, 1 - Yes P561 = 1 # H.264 payload type: between 96 ~ 127, default = 99 P562 = 99 # H.263+ (1998) payload type: between 96 ~ 127, default = 103 P573 = 103 # SRTP Mode: Disabled - 0, Enabled but not forced - 1, Enabled and forced - 2 P543 = 0 # Special Feature. 100 - Standard, 101 - Nortel MCS, 102 - BroadSoft, 104 - Sonus, 108 - CBCOM, 109 - RNK P524 = 100 ################################################################################# # End User Settings. Please do not edit this section. ################################################################################# # Web Access. 0 - HTTP, 1 - HTTPS # P900 = 0 # Web Port: HTTP default is 80 and HTTPS default is 443 # P901 = 80 # End User Password # P196 = 123 # DHCP/PPPoE support. 0 - yes, 1 - no # P8 = 0 # DHCP hostname, alphabet, max. length is 32 # P146 = # DHCP domain, alphabet, max. length is 32 # P147 = # DHCP vendor class ID, alphabet, max. length is 32 # P148 = Grandstream GXV-3000 # PPPoE support. PPPoE user ID # P82 = # PPPoE password # P83 = # PPPoE service name, max. length is 64 alpabit # P269 = # Preferred DNS server, four field, octet digits # P92 = # P93 = # P94 = # P95 = # Static IP Address. Ignore if DHCP or PPPoE is used #P9 = 192 #P10 = 168 #P11 = 0 #P12 = 1 # Subnet mask. Ignore if DHCP or PPPoE is used #P13 = 255 #P14 = 255 #P15 = 255 #P16 = 0 # Default Router. Ignore if DHCP or PPPoE is used #P17 = 192 #P18 = 168 #P19 = 1 #P20 = 1 # DNS 1. Ignore if DHCP or PPPoE is used #P21 = 192 #P22 = 168 #P23 = 0 #P24 = 1 # DNS 2. Ignore if DHCP or PPPoE is used #P25 = 0 #P26 = 0 #P27 = 0 #P28 = 0 #---------------------------------------------------------------------------------- # End User Time settings #---------------------------------------------------------------------------------- # Time Zone. Offset in minutes to GMT. # option value = 0 GMT-12:00 (International Date Line West) # option value = 60 GMT-11:00 (Midway Island, Samoa) # option value = 120 GMT-10:00 (US Hawaiian Time) # option value = 180 GMT-9:00 (US Alaska Time) # option value = 240 GMT-8:00 (US Pacific Time, Los Angeles) # option value = 300 GMT-7:00 (US Mountain Time, Denver) # option value = 360 GMT-6:00 (US Central Time, Chicago) # option value = 420 GMT-5:00 (US Eastern Time, New York), --- Default --- # option value = 450 GMT-4:30 (Venezuela) # option value = 480 GMT-4:00 (Atlantic Time, Quebec) # option value = 510 GMT-3:30 (Newfoundland) # option value = 540 GMT-3:00 (Greenland) # option value = 600 GMT-2:00 (Mid-Atlantic) # option value = 660 GMT-1:00 (Azores, Cape Verdi Is.) # option value = 720 GMT 0:00 (London, Dublin, Edinburgh, Lisbon, Casablanca, Monrovia) # option value = 780 GMT+1:00 (Paris, Amsterdam, Berlin, Rome, Vienna, Madrid, Warsaw, Brussels) # option value = 840 GMT+2:00 (Israel, Cairo, Athens, Helsinki, Istanbul, Bucuresti) # option value = 900 GMT+3:00 (Moscow, Kuwait, Baghdad, Nairobi) # option value = 930 GMT+3:30 (Tehran) # option value = 960 GMT+4:00 (Abu Dhabi, Baku) # option value = 990 GMT+4:30 (Kabul) # option value = 1020 GMT+5:00 (Islamabad, Ekaterinburg, Karachi, Tashkent) # option value = 1050 GMT+5:30 (Calcutta, Chennai, Mumbai, New Delhi) # option value = 1065 GMT+5:45 (Kathmandu) # option value = 1080 GMT+6:00 (Almaty, Astana, Dhaka, Novosibirsk) # option value = 1110 GMT+6:30 (Rangoon) # option value = 1140 GMT+7:00 (Bankok, Jakarta, Hanoi, Krasnoyarsk) # option value = 1200 GMT+8:00 (Beijing, Singapore, Taipei, Kuala Lumpur, Irkutsk, Perth) # option value = 1260 GMT+9:00 (Japan, Korea, Yakutsk) # option value = 1290 GMT+9:30 (Adelaide, Darwin) # option value = 1320 GMT+10:00 (Brisbane, Sydney, Melbourne, Canberra, Guam, Hobart) # option value = 1380 GMT+11:00 (Magadan, Solomon Is., New Caledonia) # option value = 1440 GMT+12:00 (Auckland, Wellington, Fiji) # option value = 1500 GMT+13:00 (Nuku'alofa) #--------------------------------------------------------------------------------------- P64 = 420 # Allow DHCP Option 2 to override Time Zone setting. 0 - No, 1 - Yes. # When set to Yes(1), it will override the configured Time Zone setting if available. P143 = 0 # Daylight Savings Time. 0 - no, 1 - yes P75 = 0 # Optional Rule: # If Daylight Saving Time is selected (P75 = 1), optional rule will allow automatically time ajustment based on the configured rule # Maxlength = 33, default is North America or US Daylight Saving Time Schecule: value="3,2,7,2,0;11,1,7,2,0;60" P246 = 3,2,7,2,0;11,1,7,2,0;60 # Time Display Format. 0 - 12 Hour, 1 - 24 Hour P122 = 0 # Date Display Format. 0 - Year-Month-Day, 1 - Month-Day-Year, 2 - Day-Month-Year P102 = 0 # Display Clock instead of Date. 0 - no, 1 - yes P123 = 0 #---------------------------------------------------------------------------------- # End User LCD settings #---------------------------------------------------------------------------------- # Disable SIP User Display: 0 - no (Default), 1 - yes P940 = 0 # Disable IP Address Display: 0 - no (Default), 1 - yes P941 = 0 # LCD Screen Saver Start Interval: in seconds, 0 means screen saver is off, max. length is 5 P913 = 60 # LCD Screen Saver Refresh Interval: in seconds. from 1-3600, default is 10, controls the time of screensaver image displayed on LCD. P937 = 10 # LCD Auto Power Off Interval: in seconds, 0 means LCD will be always on, max. length is 5 P909 = 0 # LCD Brightness: max. length is 5, default is 128 P910 = 128 # LCD Contrast: max. length is 5, default is 128 P911 = 128 # LCD Chroma Saturation: max. length is 5, default is 128 P912 =128 # LCD Text Color: maxlength=3 size=5 # Red (0-255) P930 = 255 # Green (0-255) P931 = 255 # Blue (0-255) P932 = 255 # LCD Background Color: value is 0 to 255 # Red P906 = 0 # Green P907 = 0 # Blue P908 = 0 # OSD Text Color: # value = 1 Blue # value = 2 Black # value = 3 Purple # value = 4 Dark Blue # value = 5 Green # value = 6 Red # value = 7 Olive # value = 8 Light Grey # value = 12 Yellow # value = 15 White P922 = 15 # PIP Position: # value=0 Top Left # value=1 Top Right # value=2 Bottom Left # value=3 Bottom Right P936 = 0 # Camera Zoom Mode: # value = 0 1.0:1 (wide and default) # value = 1 1.1:1 # value = 2 1.2:1 # value = 3 1.3:1 # value = 4 1.4:1 # value = 5 1.5:1 # value = 6 1.6:1 # value = 7 1.7:1 # value = 8 1.8:1 # value = 9 1.9:1 # value = 10 2.0:1