system toolbox

proxmox-2

# apt-get install apcupsd

proxmox-2:/lib/modules# apctest

2009-11-11 15:09:35 apctest 3.14.4 (18 May 2008) debian
Checking configuration ...
Attached to driver: apcsmart
sharenet.type = DISABLE
cable.type = CUSTOM_SMART

You are using a SMART cable type, so I'm entering SMART test mode
mode.type = APCSMART_UPS
Setting up the port ...
Hello, this is the apcupsd Cable Test program.
This part of apctest is for testing Smart UPSes.
Please select the function you want to perform.

1) Query the UPS for all known values
2) Perform a Battery Runtime Calibration
3) Abort Battery Calibration
4) Monitor Battery Calibration progress
5) Program EEPROM
6) Enter TTY mode communicating with UPS
7) Quit

Select function number: 1

I am going to run through the series of queries of the UPS
that are used in initializing apcupsd.

Simulating UPSlinkCheck ...
Wrote: Y Got: SM
Attempting to use smart_poll() ...
Sent: Y Got: SM  Good -- smart_poll() works!.

Going to ask for valid commands...
Protocol version is: 3
Alert characters are: !$%+?=#|
Command characters are: ^A^N^Z+-789>@ABCDEFGKLMNOPQRSUVWXYZ'abcefgjklmnopqrsuxyz~^M

Now running through apcupsd get_UPS capabilities().
NA  indicates that the feature is Not Available

UPS Status: 08
Line quality: FF
Reason for last transfer to batteries: S
Self-Test Status: NO
Line Voltage: 226.2
Line Voltage Max: 228.8
Line Voltage Min: 224.9
Output Voltage: 226.2
Batt level percent: 100.0
Batt voltage: 55.65
UPS Load: 017.1
Line freq: 50.00
Runtime left: 0087
UPS Internal temp: 036.0
Dip switch settings: 00
Register 1: 00
Register 2: 00
Register 3: 00
Sensitivity: H
Wakeup delay: 000
Sleep delay: 020
Low transfer voltage: 196
High transfer voltage: 253
Batt charge for return: 00
Alarm status: 0
Low battery shutdown level: 02
UPS Name: UPS_IDEN
UPS Self test interval: 336
UPS manufacture date: 02/24/06
UPS serial number: QS0609310534
Date battery replaced: 02/24/06
Output voltage when on batteries: 230
Nominal battery voltage: 048
Percent humidity: NA
Ambient temperature: NA
Firmware revision: 81.14.I
Number of external batteries installed: 000
Number of bad batteries installed: NA
UPS model as defined by UPS: MWI
UPS EPROM capabilities string: uD43132135138129uM43229234239224uA43110112114108uI43253264271280lD43103100097106lM43177172168182lA43090092081085lI43196188208204e44200155090oI43230240220225oD13115oJ13100oM13208s441HMLLq44202050710p443020180300600k4410TLNr443000060180300E443336168ON OFF
The EPROM string is 253 characters long!
Hours since last self test: NA

That is all for now.

1) Query the UPS for all known values
2) Perform a Battery Runtime Calibration
3) Abort Battery Calibration
4) Monitor Battery Calibration progress
5) Program EEPROM
6) Enter TTY mode communicating with UPS
7) Quit

Select function number: 2

First ensure that we have a good link and 
that the UPS is functionning normally.
Simulating UPSlinkCheck ...
Wrote: Y Got: SM
Attempting to use smart_poll() ...
Sent: Y Got: SM  Good -- smart_poll() works!.

Checking estimated runtime ...
Current runtime is 87 minutes
Checking for battery level ...
Battery level is 100.0 -- OK

The battery calibration should automatically end
when the battery level drops below about 25, depending
on your UPS.

I can also optionally monitor the progress
and stop the calibration if it goes below 10. However,
in the case of a new battery this may prematurely end the
calibration loosing the effect.

Do you want me to stop the calibration
if the battery level goes too low? (y/n): n

Sending Battery Calibration command. ...
UPS has initiated battery calibration.
Monitoring the calibration progress ...
To stop the calibration, enter a return.

Battery charge 100
Remaining runtime is 87 minutes
.....
Battery charge 97
Remaining runtime is 86 minutes
..

User input. Terminating calibration ...

Attempting to abort calibration ...
Response to abort request: OK
On battery 105 sec or 1m45s.

1) Query the UPS for all known values
2) Perform a Battery Runtime Calibration
3) Abort Battery Calibration
4) Monitor Battery Calibration progress
5) Program EEPROM
6) Enter TTY mode communicating with UPS
7) Quit

http://www.apcc.com/resource/include/techspec_index.cfm?base_sku=SU2200XLNET&CFID=21540085&CFTOKEN=20257555

external pack¶

That is all for now.

1) Query the UPS for all known values
2) Perform a Battery Runtime Calibration
3) Abort Battery Calibration
4) Monitor Battery Calibration progress
5) Program EEPROM
6) Enter TTY mode communicating with UPS
7) Quit

Select function number: 6

Enter an ESC character (or ctl-[) to exit.

YSM
>000
+OK
^MNA
>001

bringout@vbox-karmic-i386-1:~$ irb

irb(main):001:0> 263/60.00
=> 4.38333333333333

oooou on sad može 4 sahata radit'

Sending Battery Calibration command. ...
UPS has initiated battery calibration.
Monitoring the calibration progress ...
To stop the calibration, enter a return.

Battery charge 100
Remaining runtime is 263 minutes
.....
Battery charge 98
Remaining runtime is 258 minutes
.....
Battery charge 98
Remaining runtime is 258 minutes
..

User input. Terminating calibration ...

Attempting to abort calibration ...
Response to abort request: OK
On battery 157 sec or 2m37s.