Akcije
Podrška #18828
Zatvoren
senzori temperature, disk monitoring smartmontools, hddtemp, ventilatori
Dodano od Ernad Husremović prije više od 15 godina. Izmjenjeno prije skoro 15 godina.
Početak:
11.11.2009
Završetak:
% završeno:
0%
Procjena vremena:
Povezani tiketi 1 (0 otvoreno — 1 zatvoren)
Izmjenjeno od Ernad Husremović prije više od 15 godina
Izmjenjeno od Ernad Husremović prije više od 15 godina
# sensors-detect
root@atom-2:/etc/asterisk# sudo modprobe it87
FATAL: Error inserting it87 (/lib/modules/2.6.31-14-server/kernel/drivers/hwmon/it87.ko): Device or resource busy
dmesg kaže
[ 3067.817963] i2c /dev entries driver [ 3132.671199] it87: Found IT8718F chip at 0xa10, revision 4 [ 3132.671215] it87: in3 is VCC (+5V) [ 3132.671220] it87: in7 is VCCH (+5V Stand-By) [ 3132.671316] ACPI: I/O resource it87 [0xa15-0xa16] conflicts with ACPI region SIOR [0xa15-0xa16] [ 3132.671348] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver [ 3135.772037] it87: Found IT8718F chip at 0xa10, revision 4 [ 3135.772049] it87: in3 is VCC (+5V) [ 3135.772053] it87: in7 is VCCH (+5V Stand-By) [ 3135.772118] ACPI: I/O resource it87 [0xa15-0xa16] conflicts with ACPI region SIOR [0xa15-0xa16] [ 3135.772141] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver [ 3151.472012] it87: Found IT8718F chip at 0xa10, revision 4 [ 3151.472028] it87: in3 is VCC (+5V) [ 3151.472033] it87: in7 is VCCH (+5V Stand-By) [ 3151.472123] ACPI: I/O resource it87 [0xa15-0xa16] conflicts with ACPI region SIOR [0xa15-0xa16] [ 3151.472154] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
izgleda da acpi kontroliše ovo
Izmjenjeno od Ernad Husremović prije više od 15 godina
root@atom-2:/etc/asterisk# sensors
acpitz-virtual-0 Adapter: Virtual device temp1: +40.0°C (crit = +60.0°C)
Izmjenjeno od Ernad Husremović prije više od 15 godina
smraka-1¶
sensors-detect
#----cut here---- # You must also install and load the IPMI modules ipmi-si # Chip drivers # Warning: the required module ipmisensors is not currently installed # on your system. For status of 2.6 kernel ports check # http://www.lm-sensors.org/wiki/Devices. If driver is built # into the kernel, or unavailable, comment out the following line. ipmisensors coretemp #----cut here---- Do you want to add these lines automatically? (yes/NO)YES
Izmjenjeno od Ernad Husremović prije više od 15 godina
root@hp-smraka-1:~# sensors
coretemp-isa-0000 Adapter: ISA adapter Core 0: +36.0°C (crit = +85.0°C) coretemp-isa-0001 Adapter: ISA adapter Core 1: +39.0°C (crit = +85.0°C)
Izmjenjeno od Ernad Husremović prije više od 15 godina
malisa¶
sudo sensors-detect
#----cut here---- # Chip drivers it87 #----cut here---- Do you want to add these lines automatically? (yes/NO)YES
Izmjenjeno od Ernad Husremović prije više od 15 godina
bringout@malisa:~$ sudo sensors
it87-isa-0290 Adapter: ISA adapter VCore 1: +0.70 V (min = +4.02 V, max = +4.08 V) VCore 2: +1.04 V (min = +0.00 V, max = +4.08 V) +3.3V: +0.78 V (min = +4.02 V, max = +4.08 V) +5V: +1.32 V (min = +0.00 V, max = +6.85 V) +12V: +3.33 V (min = +0.00 V, max = +16.32 V) -12V: -19.02 V (min = -27.36 V, max = +3.93 V) -5V: -8.10 V (min = +3.96 V, max = +4.03 V) Stdby: +1.51 V (min = +0.00 V, max = +3.41 V) VBat: +2.03 V fan1: 0 RPM (min = 2732 RPM, div = 2) fan2: 0 RPM (min = 0 RPM, div = 2) fan3: 0 RPM (min = 0 RPM, div = 2) M/B Temp: +41.0°C (low = -3.0°C, high = -17.0°C) sensor = thermal diode CPU Temp: +117.0°C (low = -17.0°C, high = +127.0°C) sensor = disabled Temp3: -17.0°C (low = -1.0°C, high = -17.0°C) sensor = disabled
Izmjenjeno od Ernad Husremović prije više od 15 godina
- Naslov promijenjeno iz senzori temperature u senzori temperature, disk monitoring
Izmjenjeno od Ernad Husremović prije više od 15 godina
- Naslov promijenjeno iz senzori temperature, disk monitoring u senzori temperature, disk monitoring smartctl
malisa smartmon¶
bringout@malisa:~$ sudo apt-get install smartmontools
enable S.M.A.R.T
bringout@malisa:~$ sudo smartctl -s on /dev/sda
bringout@malisa:~$ sudo smartctl --all /dev/sda
smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.7 and 7200.7 Plus family
Device Model: ST340014A
Serial Number: 5JX1DVZX
Firmware Version: 3.06
User Capacity: 40,020,664,320 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 6
ATA Standard is: ATA/ATAPI-6 T13 1410D revision 2
Local Time is: Wed Nov 11 13:15:55 2009 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 430) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 31) minutes.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 059 054 006 Pre-fail Always - 225381301
3 Spin_Up_Time 0x0003 098 097 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 103
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 081 060 030 Pre-fail Always - 121620778
9 Power_On_Hours 0x0032 069 069 000 Old_age Always - 27658
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 475
194 Temperature_Celsius 0x0022 034 057 000 Old_age Always - 34
195 Hardware_ECC_Recovered 0x001a 059 054 000 Old_age Always - 225381301
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0
202 TA_Increase_Count 0x0032 100 253 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Izmjenjeno od Ernad Husremović prije više od 15 godina
root@hp-smraka-1:~# smartctl --all /dev/sda
smartctl version 5.37 [x86_64-unknown-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: WDC WD5000AAKS-07YGA0
Serial Number: WD-WCAS83228833
Firmware Version: 12.01C02
User Capacity: 500,107,862,016 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Wed Nov 11 13:17:27 2009 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (12600) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 147) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0003 174 170 021 Pre-fail Always - 6266
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 39
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x000e 200 200 051 Old_age Always - 0
9 Power_On_Hours 0x0032 081 081 000 Old_age Always - 13902
10 Spin_Retry_Count 0x0012 100 253 051 Old_age Always - 0
11 Calibration_Retry_Count 0x0012 100 253 051 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 35
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 26
193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 43
194 Temperature_Celsius 0x0022 110 105 000 Old_age Always - 40
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0012 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 200 200 051 Old_age Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Izmjenjeno od Ernad Husremović prije više od 15 godina
- Naslov promijenjeno iz senzori temperature, disk monitoring smartctl u senzori temperature, disk monitoring smartmontools, hddtemp
Izmjenjeno od Ernad Husremović prije više od 15 godina
atom-2 hdd¶
root@atom-2:/etc/asterisk# apt-get install smartmontools hddtem
root@atom-2:/etc/asterisk# hddtemp /dev/sda -F
/dev/sda: WDC WD1600AAJS-00L7A0: 35°C
Izmjenjeno od Ernad Husremović prije više od 15 godina
Izmjenjeno od Ernad Husremović prije više od 15 godina
Izmjenjeno od Ernad Husremović prije više od 15 godina
proxmox-2¶
lm-sensors
sensors-detect
#----cut here---- # Chip drivers it87 k8temp #----cut here---- Do you want to add these lines automatically? (yes/NO)yes
Izmjenjeno od Ernad Husremović prije više od 15 godina
na proxmoxu nisam našao modprobe
proxmox-2:/lib/modules# insmod ./2.6.24-5-pve/kernel/drivers/hwmon/hwmon-vid.ko proxmox-2:/lib/modules# insmod ./2.6.24-5-pve/kernel/drivers/hwmon/it87.ko proxmox-2:/lib/modules# find -name "k8temp*" ./2.6.24-5-pve/kernel/drivers/hwmon/k8temp.ko proxmox-2:/lib/modules# insmod ./2.6.24-5-pve/kernel/drivers/hwmon/k8temp.ko insmod: error inserting './2.6.24-5-pve/kernel/drivers/hwmon/k8temp.ko': -1 File exists
Izmjenjeno od Ernad Husremović prije više od 15 godina
proxmox-2:/lib/modules# sensors
k8temp-pci-00c3 Adapter: PCI adapter Core0 Temp: +45.0 C Core0 Temp: +40.0 C Core1 Temp: +41.0 C Core1 Temp: +38.0 C it8716-isa-0290 Adapter: ISA adapter VCore: +1.33 V (min = +4.06 V, max = +3.95 V) VDDR: +0.00 V (min = +4.02 V, max = +2.93 V) +3.3V: +3.36 V (min = +3.78 V, max = +3.92 V) +5V: +4.92 V (min = +3.39 V, max = +5.19 V) +12V: +12.16 V (min = +0.00 V, max = +6.85 V) in5: +3.02 V (min = +3.87 V, max = +0.45 V) in6: +0.00 V (min = +2.78 V, max = +3.46 V) 5VSB: +4.87 V (min = +0.00 V, max = +2.71 V) VBat: +3.07 V fan1: 3292 RPM (min = 20 RPM) fan2: 0 RPM (min = 10 RPM) fan3: 0 RPM (min = 10 RPM) temp1: +50.0 C (low = -81.0 C, high = -109.0 C) sensor = thermal diode temp2: +45.0 C (low = +93.0 C, high = -27.0 C) sensor = transistor temp3: +25.0 C (low = -3.0 C, high = +31.0 C) sensor = transistor cpu0_vid: +1.525 V
Izmjenjeno od Ernad Husremović prije više od 15 godina
atom-1 (ubuntu 8.04.3)¶
root@atom-1:~# modprobe it87
root@atom-1:~# sensors
it8718-isa-0a10 Adapter: ISA adapter in0: +2.13 V (min = +0.00 V, max = +4.08 V) in1: +2.13 V (min = +0.00 V, max = +4.08 V) in2: +2.13 V (min = +0.00 V, max = +4.08 V) in3: +2.98 V (min = +0.00 V, max = +4.08 V) in4: +2.13 V (min = +0.00 V, max = +4.08 V) in5: +0.06 V (min = +0.00 V, max = +4.08 V) in6: +0.10 V (min = +0.00 V, max = +4.08 V) in7: +2.98 V (min = +0.00 V, max = +4.08 V) in8: +3.28 V fan1: 884 RPM (min = 0 RPM) fan2: 0 RPM (min = 0 RPM) fan3: 0 RPM (min = 0 RPM) temp1: +20.0°C (low = -1.0°C, high = +127.0°C) sensor = thermal diode temp2: +43.0°C (low = -1.0°C, high = +127.0°C) sensor = transistor temp3: +53.0°C (low = -1.0°C, high = +127.0°C) sensor = thermal diode cpu0_vid: +2.050 V
Izmjenjeno od Ernad Husremović prije više od 15 godina
root@atom-1:~# hddtemp /dev/sda -F
/dev/sda: WDC WD1600AAJS-08WAA0: 37°C
Izmjenjeno od Ernad Husremović prije više od 15 godina
root@hp-smraka-1:~# sensors
coretemp-isa-0000 Adapter: ISA adapter Core 0: +37.0°C (crit = +85.0°C) coretemp-isa-0001 Adapter: ISA adapter Core 1: +37.0°C (crit = +85.0°C)
Izmjenjeno od Ernad Husremović prije skoro 15 godina
- Naslov promijenjeno iz senzori temperature, disk monitoring smartmontools, hddtemp u senzori temperature, disk monitoring smartmontools, hddtemp, ventilatori
Izmjenjeno od Ernad Husremović prije skoro 15 godina
- Status promijenjeno iz Dodijeljeno u Odbačeno
Akcije